3 Simple Ways to
Share What You Make

With Instructables you can share what you make with the world — and tap into an ever-growing community of creative experts.


Share one or more photos of a project, recipe, or whatever you've made, quickly and easily.

Step by StepStep-By-Step

Share your step-by-step photos with text instructions of what you made so others can do it too!


Share your how-to video. You'll need your embed code from a video site such as YouTube.

Easier Flashlight Mod Increases Run Time 3.6X by luxstar

Easier Flashlight Mod Increases Run Time 3.6X

We are going to take a long run time flashlight (65 hours) and turn it into a longer run time flashlight (Update:  The title of this Instructable says 3.6x run time but actual run time ended up being over 360 hours).

Yes it is another long run time flashlight hack. This one is easier than my other one. All you need a resistor, a soldering iron and this flashlight.

This Eveready flashlight (model number 5109LSH7 or 5109LS) costs $4.97 at Lowes:

(This is a great long run time flashlight to have even if you don’t do the modification.)


Where to buy:


I just picked up another one at my local Lowes. I like this flashlight because as is it has a long run time before the battery needs to be replaced (65 hours). It is bright. It is cheap and it is easy to hack. You can do this hack in 10 or 15 minutes and most of that time will be waiting for your soldering iron to heat up.

The only thing about this flashlight that is less than optimum is that the 3 LEDS have a little too much current going through them. The LEDS appear to be “straw hat” type (20 milliamp) LEDS. Each LED has about 60 milliamps running through it.

Here is a data sheet for a straw hat LED:



The LEDS in this flashlight may be specially made to handle more current but in case they are not, this modification will bring the current down to a level that will insure tens of thousands of hours of LED life.

I chose to add a 56 ohm resistor to the circuit so each LED runs at about 16.5 milliamps. This will increase the run time by 3.6 times.

The other step by step instructable to make a long run time flashlight is here:


Either one will be good to have in an extended power outage.

Step 1


You will need to unscrew the black ring that hold the clear plastic cover on the front of the flashlight. Then remove the assembly shown in the picture above. Install the battery and re-assemble the flashlight. Test the flashlight to make sure it works. Remove the rind and assembly shown in the picture above. Un-solder one of the two red wires from it’s metal contact. I chose the one on the left.

Step 2

Solder The Resistor

Now lets select a resistor. I chose a 56 ohm resistor which reduced the current in the circuit going to the 3 LEDS to 50 milliamps (it was 180 milliamps before the modification). Here are some other resistor values and the currents I measured:

44 ohms (two 22 ohm in series) = 56 milliamps

You may want to try out some other resistors for longer run time or higher brightness. I was going for 200+ hours of run time which is about a month of use if used 6 hours a day.

100 ohms = 31 milliamps

Solder one end of the resistor to the metal contact and the other end of the resistor to the wire that was originally attached to the metal contact.

Step 3


The first picture shows the light from an unmodified flashlight on the left and a modified flashlight on the right. Note that the light on the right is produced using 3.6 times less power or about 28% of the power to produce the light on the left. The picture of the warning sign was taken using only the light from the modified flashlight at a distance of 18 feet (camera on zoom).


Long run time flashlights make great gifts. Make several for the people on your gift list. They are also great for emergencies. This one is good for a 3.6 x bigger emergency.


Update 11-10-12.

I started a test to see how long the batteries would last running 24 hours a day. The test started on the morning of 10-26-12. I was expecting a 200 hour run time. After 15 days (360 hours). The flashlight still puts out a usable amount of light. I can still read with it without any problem. I also got the opinion of a fellow flashlight enthusiast who thinks the flashlight is still useful for its intended purpose which is for the user to be able to easily see their way around the house in the dark and be able to easily read. The flashlight is noticeably dimmer than it was at the beginning of the test so I would conclude that this is a 360 hour flashlight. It has exceeded my expectations because the run time has been increased 5.5x. If I was using this flashlight 6 hours a day the test would have taken 60 days to get to this point.

If this had been a real emergency I would gladly use this flashlight several more days.


See all my instructables here:




fretted says: Nov 22, 2012. 10:12 AM
Ok i'm going to give this a shot i have to get some batteries but i have some of these flashlights laying about can't hurt to give it a shot thanks for this great idea you made it easy for me to understand and teach to my kids too .....
luxstar (author) says: Oct 26, 2012. 6:11 AM
(removed by author or community request)
luxstar (author) says: Nov 6, 2012. 10:33 PM
(removed by author or community request)

Get More Out of Instructables

Already have an Account?


PDF Downloads
As a Pro member, you will gain access to download any Instructable in the PDF format. You also have the ability to customize your PDF download.

Upgrade to Pro today!